TIPS ABOUT HOW TO Extend Smok Pen Recharge Time
The Smok Pen is a new pen that was created by two guys in California. They wished to create a cool writing instrument that appeared as if a real pen but had the opportunity to smoke a hookah. They named their product the Smok Valve and the Smok Pen. The Smok Valve has had the market by storm.
The Smok Pen includes a built quality that’s just great. I found that even though it can be an electronic pen the construction is simply as good as the pens that I have reviewed. For the reason that of how they made the top cap. You don’t have to worry about the cap cracking or breaking on you Smok Valve Pen.
The two biggest differences that separate the Smok Valve from other pens is the shape of the coils and the way that they are built. In general the coil on a Smok Pen is larger than on other pens. I think that they did this on purpose, to make the pen feel more substantial.
If you take a glance at a Smok Pen, you will notice that your body of the pen is round rather than smooth like other pens. On the trunk of the pen there exists a little tab that houses the coil. Once you press on the tab you can actually turn the heating element on / off. I must say i liked this feature since it allows me to utilize the Smok Pen 22 whenever I feel like smoking.
To use the Smok Pen you have to keep carefully the heat button pressed. After the button is pressed, the heating element will start to warm up. Once it gets to the appropriate temperature you can switch off the heating element. Smok recommends utilizing a 22mm tank. I prefer a more substantial tank, but that’s just me.
Once you put your Smok Pen into the tank you will see a indicator light seriously. The indicator light will remain green if you don’t put your Smok Pen into the Smok Pen charger. Once your Smok Pen has entered the charger the indicator light will turn red. It is very important always put your pen into the charger before you apply the e-liquids to the coil heads. Additionally it is important to do that before putting your e-liquids in to the coil heads.
Once you have completed this step, it is best to check to see should you be at the proper temperature for the coils to fire. Or even then you should turn the energy off and try again. For anyone who is still not satisfied with your Smok Pen i quickly suggest you take it in for some troubleshooting. This is exactly what I’d call the “troubleshooting process” because sometimes things just do not work as they should. I would recommend that you perform the next two steps, then go on and check the Smok Pen to see if it still has the electronic charging port.
Prior to going any further you should remove the battery from your own pen and unscrew the magnetic cap. You need to then remove the plastic sleeve that holds the sub-ohm. There is a wire that runs through the Smok’s body which is green in color. You need to loosen this wire using pliers. After you have loosened this wire after that you can access the sub-ohm. You should then take away the wire from the Smok’s body and carefully insert it into the Smok pen’s electrical port, being careful to not touch the coils.
After you have placed the sub-ohm tank into the pen you need to then place the rest of the components including the wattage, the batteries and the heating element into the included microwaveable microwave oven. Start the power and follow the on screen instructions. You should place the pen’s battery into the microwave and activate the setting. You should then wait approximately 30 seconds before turning it back off. When you initially put the pen into the microwave the electronic reading will show a low voltage protection setting. If this setting will not automatically get Element Vape Coupon set then you should follow the on screen instructions.
Once the Smok Pen has already reached the temperature that it needs to reach you need to then connect both wires to the positive and negative on the positive post on the Smok unit. You need to then connect the other end of the battery to the negative post on the negative side of the Smok unit. The final step would be to connect the positive cable to underneath of the Smok’s power switch.
After all of the components have been placed in to the pen, you should turn the energy on. After the first test run, you ought to be able to see the battery life indicator light seriously. If you do not see any sign of life from the Smok Pen, you need to take away the battery from the pen and replace it with a fresh one. For your convenience gleam green light that could be pressed so as to confirm the battery charging status. Once you have done these things and you also do not see the green light indicating charging, you should replace the battery.